Training Alignment Pump and Motor

bigstock Team of technicians using digi 71351170 - Training Alignment Pump and Motor

Training Alignment Pump and Motor-Pump alignment is the process of aligning shaft centerlines between a motor and a pump. The motor is the prime mover, transferring power to the pump by the use of a coupling. This is probably the most common configuration of coupled machines in industry.

In this type of alignment, the motor is almost always the moveable machine, and the pump is the stationary machine. In almost all cases, the pump is already piped up with suction and discharge flanges, which means it can move only slightly, if at all.

motor-pump-alignmentProper shaft alignment is achieved by moving the motor. The motor is shimmed vertically to achieve the proper elevation to align it to the pump, both parallel (offset) and angular. The motor is them moved horizontally to achieve proper horizontal placement for aligning the shaft centerlines, both parallel and angular. The motor is moved horizontally by the use of jacking bolts, or by the use of pry bars, hammers, or other tools.
Motors are normally easier to move, since the motor is not piped into a process system. A short run of flexible conduit is most often used to run the electrical wiring from a local disconnect, or a rigid conduit, to the motor termination box. This allows for ease of movement of the motor.

Training Alignment Pump and Motor

Materi Training Alignment Pump and Motor

1. Fundamental Alignment
2. Diagnosing Misalignment
3. Measuring Misalignment
4. Preparing Task Alignment
5. Alignment Methods (praktis)
•Rough Methods
•Face and Rim
6. Alignment Tolerances
7. Complicating Factor Alignment.
8. Introduction to Laser Alignment
9. Minimizes the forces of misalignment acting upon the bearings and seals of both components.
10. Minimizes Wear of The Coupling.
11. Reduce Energy Costs.
12. Maximizes the life of the Machine Components by Minimizing Wear, ncreasing time between failures, and reducing vibration.

Method Training Alignment Pump and Motor

•Presentation
•Discussion
•Simulation
•Case Study
•Evaluation

Fasilitas Training
  • Lokasi Training di Hotel Bintang 3-5
  • Sertifikat Training
  • Modul Materi (Hard Copy & Soft Copy)
  • Flashdisk
  • Training Kit (Co-Card, Bolpoin, & Buku Catatan)
  • Souvenir Eksklusif
  • 1x Makan Siang dan 2x Coffee Break (Jam 10:00 & 14:00)
  • Penjemputan Bandara – Hotel (Pulang-Pergi selama pelatihan)
Biaya dan Lokasi Training
  • Yogyakarta : Rp 6.800.000,- / Peserta
  • Bandung : Rp 7.600.000,- / Peserta
  • Jakarta : Rp 7.800.000,- / Peserta
  • Surabaya : Rp 7.800.000,- / Peserta
  • Malang : Rp 7.800.000,- / Peserta
  • Semarang : Rp 7.200.000,- / Peserta
  • Solo : Rp 7.500.000,- / Peserta
  • Bali : Rp 7.000.000,- / Peserta (Minimal 2 peserta)
  • Lombok: Rp 7.400.000,- / Peserta (Minimal 2 peserta)
Keterangan
  • Biaya diatas jika 1 perusahaan hanya mengirimkan 1 peserta.
  • Jumlah peserta memperngaruhi biaya diatas, jadi jika 1 perusahaan mengirimkan 2 atau lebih peserta maka biayanya dapat dibawah (turun) dari biaya yang tertera diatas.
  • Biaya dan Lokasi diatas hanya untuk Private Training dan Public Training, untuk In House Training penawarannya dapat menghubungi kami dilink berikut (kontak kami).
  • Jumlah peserta, jadwal training dan lokasi training dapat menyesuaikan permintaan.
  • Pemintaan lokasi yang diluar daftar diatas dapat menghubungi kontak Marketing Kami.

Untuk melihat jadwal pelatihan ini kunjungi Jadwal Training Update dan jika ingin mendaftar pelatihan ini, silakan isi form di Formulir Pendaftaran.

 

output k4bSCJ - Training Alignment Pump and Motor

Formulir Pendaftaran

Contoh ; 29-30 Desember 2020

Tinggalkan Balasan

Alamat email Anda tidak akan dipublikasikan. Ruas yang wajib ditandai *